Original subtitles

In this video, we are going to create the lower portion of the example 17 file.

You can see here, this is the lower portion that we are going to create.

Now, let's open the file that we have heard in the last video and go to file open, we have seen it

in the desktop.

Example 17 click on Open.

You can see here we are in the partisan interface of that file.

If you want to enter into the sets that you have created, just double click on this sketch and you

will get into the sketcher interface.

Of this catch.

None of it is clear the lower portion.

Let us first create two circles.

A circle here.

And another circle here.

Now, will tech access double click on access this point?

This Centrepoint.

And this Centrepoint.

To the central point will create two axes, let us select the axis and make it vertical, select this

axis and make it vertical.

Now, let us give the dimentia the one click on dimensioning, let us give a dimension to this axis.

This is 175 and this axis is of length one 130 plus 20, 150, 130 plus 20.

Now, let us give the details of these two circles.

Select this circle, double click, this is over, it is 100.

In selected areas, I'm 100.

Similarly here, this is of religious value, 120, you can see here it is not getting constrained.

There is some problem.

And you can see this point is not getting coincident with this point, so we'll just do we'll take the

axis point and this center point.

Coincidence.

And this has been constrained.

Now we'll take Veillette, select this circle and this circle.

You can see it is getting trimmed.

I use the control plastic to undo the flat and here will take no trim, click on neutral, select this

circle and the circle.

You can see if it has been created.

Double click.

This radius is 50.

Similarly will click on Select.

From the circle to this line.

Click double click on this, flip this over just 20, double click on Quick Trim and then this portion.

This portion, this portion, this portion.

Three mile, this distribution.

Prisoner escape, key exit from the Trimingham on heavily guarded line as a tangent to these two circles.

So Altec by tangent line.

From this circle to the circle immediately and go for quick trim, you can see we have created the boundary,

not let us create the other components inside it.

Let us select a circle.

Let me create a circle here.

You can see a lot of interferences there, Elkadi, circle this circle, and this is coincidence dimensioning.

Between this point and this point, this is a value 20.

This circle is of diameter.

40.

You can see we've created the circle.

Now will create a elongated Houllier.

And taking third profile predefine profile, cylindrical, elongated hole will take this center.

And create this fine.

And create a spine from here to here.

You can see the it they're looking at, it immediately will give a radius value of 20.

We'll take dimensioning will take this big circle radius, which is of value added.

Now he require the start and then this total angelis 120 degrees so we can take axes or we can take

a line and make it.

Construction element.

Double click on Nexis, let us take Axis.

From this point to this center point, again, from this point to the central point person, the escape

key now will take dimension from here to here.

This is of value one end.

And I mention again from this access to this access.

This is a value 122 to 60.

This completely constrained.

Now take line DoubleClick online.

I'll make a vertical line here.

Another vertical line here.

Plus there simply to exit from the command.

Niantic Dimensioning.

From here.

To this center.

Developing this value is then.

Niantic dimensioning from this line to this line, don't like this value is 20 immediately I'll take

quick trim them the unnecessary portions.

You can see are from the figure, but we have to make this flat so they will click on Flat.

That is Duminy with.

Select this line and disco.

We want to trim it, so I use trim all elements.

Don't click here, this validates them.

And double click here.

This will result something.

Non-liquid Tim Tim Distribution's.

So we have completed this figure and it is Jumoke.

Oh, you can see we have rotated the view, so I'll click on normal.

You click on it and we will get another one of you.

Not to assume and focus on this area, let us create the intel stuff.

First, let me take a circle and take this center and create a circle.

This diamond jubilee is 80, take a rectangle.

And create a rectangle here.

Double click on dimensioning, the width of this rectangle is 20.

And from here to here, this will stem from this line to the center.

This will be 70.

Now will take good trim and trim the necessary portions D-line.

This line, this line, and here not let us take this, select this object, use the control key for

multiple selection.

Rooted.

About this central point, taking this point is reference.

You can see we require total eight objects, so including the sole object, it is eight.

So here we require seven instances.

You can see we are creating seven instances and the angle will be 360, divided by eight.

You can see we have created eight objects in total.

Now, let us double click on Quick to.

And unnecessary Pushtuns.

Now, let us it.

By selecting their line.

And fixing.

You can select the line, even you can select all the lines and fix it together.

It's not a problem.

But you have to create a completely constant geometry.

And you can see.

The figure is completely constrained.

Now, let's focus in this area.

Selected circle.

And make a circle somewhere here.

A lot of disturbances there.

It does take the circle somewhere here.

It is great to access.

From the center will create axis and now will do the damage from here to this axis, this dimension

is 12.

Again, we'll take dimensioning from this access to this Centrepoint, this value is 50.

Now will take dimension of this circle, this Radiuses eight.

Will Juman now take a rectangle and make your profile something like this, take dimensioning.

This length is 10.

Double click on Dimensioning from this line.

To this point, this is ten divided by two, which is five now from this point to this line.

This is all sort of evaluating.

Now immediately will take a victim in this portion, this portion, this portion and this portion.

We have created a single geometry, how we translate this.

Select the object that you want to translate.

Goodwin said Operation Transformation.

Translated from this point, five number of instances we want to create, including the base object,

it will be six.

And the land value is 24.

You have to just position it now.

You can see it is locking here, so this is completely horizontal click, you can see we have made that.

Upline, now we have to make the bottom line before that, let us constrain this geometry.

Select the subject.

And fix.

Similarly, you can select this object, use the control button for multiple selection.

Fixx.

Now will select all these objects.

Select all this object.

Translate.

From this center point.

Towards Don.

Only one instance we will create.

And the land values, 15 plus 12.

And.

And when I create when I click, you can see here this object is intersecting with this object, but

you can see the drawing.

There is a lot of gap.

So we have done some error in our sketching.

You can see here there is a gap, but you know what, these two are intersecting.

So let us find out where is the problem?

Let us do more and let us analyze where is the problem?

Analyzing a problem that you have encountered is very important for making complex drawings because

you cannot delete or create a new file every time and start over again.

So let us edit it, you can see here these two are interfering.

So there must be some problem with this.

Geometry, let us find out what I think is there must be some problem with this angle.

This is 120 degree and this is 60 degrees.

The values are correct, but.

Let us see that drawing again, you can see here this is one 120.

Not angle, but it has been generated from this point, not this point, we have the angle from this

point.

So that is the problem.

Let us change it for changing it first.

Delete these triangles.

Next, delete these two lines.

Double click on access.

From this point.

To this central point.

Again, from this point to this center, point will create the axis.

It is good angle double click on Dimensioning from here to here, this angle is 120 degrees and from

this line to this line.

This is 60 degrees now, you can see we have achieved over geometry.

Now let us constrain this.

Select all the objects and.

Silicon constraining fix, click on OK, now over geometry is complete, hence we have completely,

fully constrained examples, 17 drawing that we needed to make in this series of two videos.