Original subtitles

‫Hey, guys, welcome back to yet another radio on this we do want to start creating our floor slabs

‫and also a roofing.

‫So I'm going to make the site first.

‫So what you can do is press the line tool.

‫So like once.

‫The second time.

‫13 and 14.

‫It doesn't create.

‫Just go back to the first point.

‫And you create your rectangle on Double-Click on the rectangle plus two to make it a group.

‫Go to the group and give an offset.

‫So this wall is at on hundred women generally accomplished is thicker than this, but you would keep

‫it at a hundred and.

‫No.

‫No, we can delete the entire rectangle and now we can give our component all height.

‫So I'm going to give a height of around four feet.

‫In India, most buildings are made with the cardboard.

‫And it's not really open because there is a lot of theft that happens.

‫We can also make our opening for our gate.

‫I'm going to quickly switch to perspective mode because it's easier to model in 3D while in perspective

‫mode compared to power projection.

‫So make a rectangle and then push to zone double click on the surface.

‫And then delete.

‫Who's this Phyllis Edge?

‫And push this to the stage.

‫So going to have a sliding get.

‫Can create a floor slabs.

‫So press on on your keyboard to make a rectangle or make a rectangle in this age, double click G to

‫make it a group again, a process which is a scale command and scale this edge to this edge.

‫All right.

‫So we're going to have a plane to one foot, so go into the group projects out by one foot.

‫Which also means that we need to push our whole stop by one foot as well.

‫Someone's up by one foot.

‫No dog got out, just not going to be a one foot plant.

‫So, I mean, could a candidate to sway and push the stone?

‫But this floor starts at one foot.

‫So make a rectangle again.

‫Not to make two steps.

‫I simply need to create a rectangle.

‫So this is one foot or 300 M in the trade size is one foot.

‫And that Aysel, is six inches.

‫So lumber clay is due to make it a group.

‫So what this thread does along the side of the step and razor is your height.

‫So a height of six inches.

‫More this up.

‫Making a copy.

‫Move it up and then you can move this, as all you can do is go into the scoop and stick to.

‫So we had our steps.

‫Maybe I don't want to step to politics so much into space, so I'm just going to push back a bit.

‫May have to check the door swing, which is three feet.

‫OK.

‫So the reason why we have such a big landing is because the main door is you.

‫And it has to occupy the full swings.

‫Those are certain subtleties and design to develop over a period of time.

‫All bets are off plenteous created.

‫No, we can create a flow slap.

‫What you can do is copy the splint on top to press emond and crystal control key to make a copy.

‫It's not able to snap out of the blue axis.

‫So what do you have to do is press the top rookie snaps it to the blue Xs place at your.

‫I'll go this group is due to.

‫Is it ready?

‫So this is one foot.

‫Which is 300, if I am going to bring this back to six inches, because six inches, a typical slab

‫thickness in India.

‫Sometimes is known to even four inches.

‫This is oil lapping gently in construction.

‫What happens is the flow comes below the slab and then we hold out the beams in you.

‫But since this a visualization goes, not going to go in depth on the construction detail.

‫It's more for your initial visualization and to impress your clients.

‫So what you can do is this push these slabs in surprisingly and push these in.

‫Was the sweet as well.

‫Make a rectangle, you know, and push this down to make an opening.

‫This is a staircase is opening, so we'll have to push this out as well.

‫Put Date Douglas ready on this landing and comes up, comes out a bit.

‫So it comes out in the edge of the step, so museum dog is a pretty and extreme mood to work more efficiently

‫and faster, as you can see, make a rectangle again.

‫And predictors don't.

‫Projects to this edge and neocortical.

‫No, we can copy the slap to the top.

‫It also covers a bedroom.

‫So go into the group.

‫You.

‫And push this out into this edge.

‫And covered this out.

‫Now, 40 hour bathroom, generally, the slab is not at the same level.

‫We generally have a draw for our bathroom.

‫It's called a sunken slab.

‫So these slabs are gently art ten feet.

‫And these slabs, which is in the bathrooms, they are sunk down by one and our feet.

‫Now, we'll be talking more about this in the Revit course, which is coming out soon.

‫Copy this.

‫And copy it to the top.

‫We can create a B.M..

‫We can leave it as is.

‫You can maybe even push this in.

‫We have a beam as well.

‫So I'm going to push this in by six inches.

‫This.

‫That is a bashing on the back, so he can lead that as Aziz.

‫All right.

‫So we've created our floor slabs.

‫We can all create a roofing slab so we can just copy this again on top.

‫Control and make a copy to the top.

‫So you are 10 feet, 10 feet in another infuser, 30 feet in total.

‫No, our slab is sloping, so we can just push this in the edge.

‫What we could do is also make sure these extra rectangles are deleted, supposedly make a group and

‫then delete.

‫I'll select this face without a snapper to the red.

‫Where pressing the right key and place it on the face of this wall.

‫Predict this oak.

‫Select this purple flake to select both the faces and edges of the dial.

‫So first press G again.

‫So this is a nested group within a group.

‫Now we're going to rotate this.

‫So Priscu.

‫I'm going to select this point as my axis of rotation.

‫And this is my angle reference to raw data to just H.

‫Now we can go to this group and then we should do the sage.

‫So now we have certain openings.

‫There's a carto deal.

‫And this also is going to be a sunken slab, which is because we're going to give a guardino.

‫So now we can go ahead and make an opening, so first we need to make a rectangle up with this edge.

‫Press F to actually it a schedule and then offset it out by around 600 M.

‫So like the first press be to act with the Bush doland Bush does, Don.

‫So that creates an opening that.

‫You can also create an opening in slab roof slab.

‫So I'm going to make two lines first.

‫There's one line.

‫It also has to be in the same axis.

‫Always make sure you're snapping into the green or at axis while modeling makes it more efficient.

‫I was derided this.

‫And the way to as well.

‫So we are two faces.

‫What I am trying to do is match it along this wall thickness.

‫So there's more harmony in valuation.

‫Now I'm going to give an offset of around 600 Eman.

‫And make an opening here.

‫Similarly, this as well.

‫Now, these don't have to go all the way up.

‫So we bring them down a bit, but make sure that the appearance height, which is mean, just go.

‫I'd say the group.

‫From your to your thousand eight dhody, which is six feet, so it has to be at least seven feet so

‫that your user doesn't keep banging into it.

‫So, for example, five or seven feet human being is gonna be banging his head into this lap if it's

‫only up to six feet.

‫So make sure there's enough clearance.

‫We can make a rectangle, you know.

‫Make this a group and projected out.

‫Project assault all the way to.

‫I'm going to make a line.

‫So from dosage, dosage, so that the weights to face it doesn't divided because we didn't draw it in

‫the current axis.

‫So from this edge of dosage.

‫All right, so now it's divided the face and now we can choose to vote.

‫Again, select as well and copy to the other side.

‫All right, great.

‫We have a B.M..

‫So that is around one and a half feet or two feet in depth.

‫So we're going to give our depth of our own two feet.

‫So two feet and two.

‫Rosie to make it a group until the group and then projected.

‫Now, you don't have to worry about these extra lines which are showing up.

‫It all gets hidden when you're doing the reading render.

‫But in case you want to hide them, what you can do is go into the wall.

‫Plus E to actuator eraser tool and press shift and delete.

‫So lines.

‫And you need to also go to the bottom one and delete these lines.

‫So now you can see that these lines get deleted.

‫And looks like it's one face.

‫I wouldn't recommend it because in retail, generally, it hides the line automatically.

‫We have some beams, Yoda's when.

‫So I'm going to make a rectangular B.M. type in two feet.

‫And press enter.

‫So it goes this way.

‫So we need to type and call my two feet.

‫So comma and then two feet.

‫So takes this dimension automatically and gives a depth of two feet.

‫DoubleClick Prezzie to make it a group.

‫Projected out this way.

‫And projected that Greensmith.

‫No.

‫One, my illusions are like the lines to match.

‫Now you can see that it goes up this way.

‫What I can do is go to this beam and then just projector's zone up to the little level.

‫So what happens is they give a beam of around two feet and below the beam they give a wire mesh, which

‫is only around 50 M-m or two inches.

‫I know this is such a big cantilevers and it cannot be supported without columns.

‫So we have alternate columns to give as well.

‫So I'm going to give you a white column, which is generally a steel column.

‫So I'm going to make a circle.

‫No.

‫So pressie to make a circle.

‫I'm going to give a radius of around Sandy Faymann.

‫So that's a six inch stone column, select a column and press G to make it a group.

‫To the group and projected.

‫Oh, I put that edge.

‫And also make sure you push it out.

‫Snapper to go Green, Accies and Shadow.

‫I'm going to hide the compound wall for No.

‫Move this in, what you can do is rotated so Priscu at 42 and Geens axis of rotation.

‫So Presto left out Ocky to activate the green axis.

‫Now I'm going to select the midpoint.

‫Yo, I'm going to rotate this this way.

‫And I'm a little Priscu again.

‫And rotated to the other side.

‫But this time I may have called PEBO pissing the country Weeki.

‫Also, make sure you go into the group and project them.

‫Sweet and sweet as.

‫Make them a group with your record and then just push them in a bit.

‫All right, great.

‫I can scale them down a bit.

‫So that doesn't look like it's jutting out of the beam or column.

‫You made it quite two columns.

‫I'm here to get the structure running from the structural engineer.

‫But for now, let's keep two columns.

‫Or maybe one column would do the job.

‫So it's his fault.

‫Yeah, I think the suctions and I should be able to calculate that.

‫Lord.

‫So our elevation is taking shape.

‫No, no, in the next video, we're gonna learn to model windows and then place them in place and also

‫create doors and the remaining parts of the margin.

‫So I'll see you guys in the next video shows.