Would you like to inspect the original subtitles? These are the user uploaded subtitles that are being translated:
1
00:00:00,240 --> 00:00:02,159
hey guys i'm zach welcome back to bear
2
00:00:02,159 --> 00:00:03,919
mountain builds and today i'm going to
3
00:00:03,919 --> 00:00:06,000
show you how simple it is to install a
4
00:00:06,000 --> 00:00:07,250
t-track
5
00:00:07,250 --> 00:00:21,349
[Music]
6
00:00:21,359 --> 00:00:23,519
so i put t-tracks into a couple of my
7
00:00:23,519 --> 00:00:26,160
projects now and i really love them and
8
00:00:26,160 --> 00:00:27,760
a lot of you seem to like it too so
9
00:00:27,760 --> 00:00:29,519
you've been leaving comments asking how
10
00:00:29,519 --> 00:00:31,840
i actually did that so i thought i'd put
11
00:00:31,840 --> 00:00:33,600
together this short video about how to
12
00:00:33,600 --> 00:00:35,680
install t-track it really is super
13
00:00:35,680 --> 00:00:37,680
simple all you need to be able to do is
14
00:00:37,680 --> 00:00:40,160
measure and have a router now i just so
15
00:00:40,160 --> 00:00:41,680
happen to have some t-track that i've
16
00:00:41,680 --> 00:00:42,960
been meaning to put into the other side
17
00:00:42,960 --> 00:00:45,039
of my miter saw table over there
18
00:00:45,039 --> 00:00:46,239
and
19
00:00:46,239 --> 00:00:48,960
i just got a new battery powered 20 volt
20
00:00:48,960 --> 00:00:51,440
max compact dewalt router and
21
00:00:51,440 --> 00:00:53,120
i am super excited to use one of these
22
00:00:53,120 --> 00:00:54,640
i've never used a battery-powered router
23
00:00:54,640 --> 00:00:56,719
before so i'll give you a review of this
24
00:00:56,719 --> 00:00:58,559
too now let's get started
25
00:00:58,559 --> 00:01:00,399
now for this video i'm gonna be assuming
26
00:01:00,399 --> 00:01:02,239
you know how to use a router but i will
27
00:01:02,239 --> 00:01:04,080
be going over my setup for my depth of
28
00:01:04,080 --> 00:01:06,479
cut now i'm using a three-quarter inch
29
00:01:06,479 --> 00:01:08,000
bit because my t-tracks are
30
00:01:08,000 --> 00:01:09,680
three-quarter inches wide so that way i
31
00:01:09,680 --> 00:01:11,040
don't have to worry about doing multiple
32
00:01:11,040 --> 00:01:12,880
cuts or anything so first off i'm going
33
00:01:12,880 --> 00:01:14,640
to take a test piece of wood lay that
34
00:01:14,640 --> 00:01:16,960
down and then put two t-tracks on top of
35
00:01:16,960 --> 00:01:17,680
it
36
00:01:17,680 --> 00:01:20,000
and then i will set my router down on
37
00:01:20,000 --> 00:01:22,240
top of those two t-tracks and i'm going
38
00:01:22,240 --> 00:01:25,280
to slowly pull it along as i push the
39
00:01:25,280 --> 00:01:27,680
bit down further until i feel the bit
40
00:01:27,680 --> 00:01:29,600
touch the wood because my sliding will
41
00:01:29,600 --> 00:01:31,680
have stopped
42
00:01:31,680 --> 00:01:33,840
see and there it is i'm at the right
43
00:01:33,840 --> 00:01:36,799
depth now so i can lock it off and now i
44
00:01:36,799 --> 00:01:38,840
can do a test cut
45
00:01:38,840 --> 00:01:42,000
now to start off i've put down a
46
00:01:42,000 --> 00:01:44,240
straight edge on my test piece of wood
47
00:01:44,240 --> 00:01:46,399
and i'm going to draw a line
48
00:01:46,399 --> 00:01:48,000
right where the straight edge is right
49
00:01:48,000 --> 00:01:49,280
now
50
00:01:49,280 --> 00:01:50,720
and then
51
00:01:50,720 --> 00:01:52,799
i'll put my router up against it i'm
52
00:01:52,799 --> 00:01:54,320
going to cut about six inches so i can
53
00:01:54,320 --> 00:01:56,320
get a field if my t-track fits well or
54
00:01:56,320 --> 00:01:56,870
not
55
00:01:56,870 --> 00:02:00,850
[Music]
56
00:02:00,850 --> 00:02:04,079
[Applause]
57
00:02:04,079 --> 00:02:06,079
now that i have my test cut done i can
58
00:02:06,079 --> 00:02:07,759
make sure that the depth is correct with
59
00:02:07,759 --> 00:02:09,520
my t-track so i can just shove it in
60
00:02:09,520 --> 00:02:11,360
here
61
00:02:11,360 --> 00:02:13,200
and it feels really good it's like
62
00:02:13,200 --> 00:02:14,879
basically perfectly flush so this is
63
00:02:14,879 --> 00:02:17,840
really good and then i can pull this out
64
00:02:17,840 --> 00:02:20,000
and take my straight edge off
65
00:02:20,000 --> 00:02:21,120
right here
66
00:02:21,120 --> 00:02:23,680
and i still have a line made to the edge
67
00:02:23,680 --> 00:02:24,879
of my cut
68
00:02:24,879 --> 00:02:26,720
and i can take a tape measure
69
00:02:26,720 --> 00:02:28,480
and measure the distance from my cut to
70
00:02:28,480 --> 00:02:30,000
the line
71
00:02:30,000 --> 00:02:32,560
which looks like it is one and five
72
00:02:32,560 --> 00:02:34,319
eighths and now i know that's where i
73
00:02:34,319 --> 00:02:36,959
need to mark on my final cut for where
74
00:02:36,959 --> 00:02:38,400
my straight edge needs to go versus
75
00:02:38,400 --> 00:02:40,800
where i actually want my cut to be
76
00:02:40,800 --> 00:02:42,160
all right so here's the left side of my
77
00:02:42,160 --> 00:02:43,680
miter saw table and this is where i'm
78
00:02:43,680 --> 00:02:45,680
going to be putting my t-track in
79
00:02:45,680 --> 00:02:47,280
now what i've done to start off with is
80
00:02:47,280 --> 00:02:49,760
i put down painters tape on both sides
81
00:02:49,760 --> 00:02:51,599
this lets me make marks on this without
82
00:02:51,599 --> 00:02:53,360
having to worry about marring the wood
83
00:02:53,360 --> 00:02:55,200
and it will protect the wood from being
84
00:02:55,200 --> 00:02:56,800
blown out when i put the router through
85
00:02:56,800 --> 00:02:57,599
it
86
00:02:57,599 --> 00:02:59,840
now what i want here is my t-track to
87
00:02:59,840 --> 00:03:01,440
have a spacing of three-quarter inches
88
00:03:01,440 --> 00:03:03,599
between the face of my fence to the edge
89
00:03:03,599 --> 00:03:04,959
of the t-track
90
00:03:04,959 --> 00:03:07,360
so i've made a mark where i measured out
91
00:03:07,360 --> 00:03:09,599
three-quarter inches right here and then
92
00:03:09,599 --> 00:03:10,959
i need to make a mark for my straight
93
00:03:10,959 --> 00:03:13,440
edge which i measured before is an inch
94
00:03:13,440 --> 00:03:16,159
and five-eighths away so i measured from
95
00:03:16,159 --> 00:03:19,040
this point right here back to here and
96
00:03:19,040 --> 00:03:20,319
that is where i'm going to be putting my
97
00:03:20,319 --> 00:03:22,080
straight edge so for this side i've made
98
00:03:22,080 --> 00:03:23,519
marks for where my t-track is going to
99
00:03:23,519 --> 00:03:25,519
go right here and i have made another
100
00:03:25,519 --> 00:03:28,640
mark for where my straightedge will be
101
00:03:28,640 --> 00:03:30,640
now let's get this fence off and start
102
00:03:30,640 --> 00:03:35,160
cutting
103
00:03:35,170 --> 00:03:49,110
[Music]
104
00:03:49,120 --> 00:03:50,959
i'm really impressed with the weight and
105
00:03:50,959 --> 00:03:53,120
power of this dewalt compact router it
106
00:03:53,120 --> 00:03:55,120
seems to cut just as easily as my corded
107
00:03:55,120 --> 00:03:59,520
bosch router
108
00:03:59,530 --> 00:04:07,429
[Music]
109
00:04:07,439 --> 00:04:08,970
do
110
00:04:08,970 --> 00:04:24,160
[Music]
111
00:04:24,160 --> 00:04:26,400
now the cut turned out pretty well but i
112
00:04:26,400 --> 00:04:28,080
felt the adjustment ring on the router
113
00:04:28,080 --> 00:04:30,320
spin just a little while i was cutting
114
00:04:30,320 --> 00:04:32,000
this ended up making my channel deepen
115
00:04:32,000 --> 00:04:33,919
by about a thirty second of an inch
116
00:04:33,919 --> 00:04:35,919
which isn't a really big deal but since
117
00:04:35,919 --> 00:04:37,840
i do have a black milling top i can see
118
00:04:37,840 --> 00:04:40,080
that the t-track isn't flush however
119
00:04:40,080 --> 00:04:42,240
there is an easy fix above laying five
120
00:04:42,240 --> 00:04:44,000
strips of three-quarter inch tape down
121
00:04:44,000 --> 00:04:45,600
the channel this will just bump that
122
00:04:45,600 --> 00:04:47,120
t-track up a little bit and make it
123
00:04:47,120 --> 00:04:48,260
flush
124
00:04:48,260 --> 00:04:54,469
[Music]
125
00:04:54,479 --> 00:04:56,639
now this is more my fault than anything
126
00:04:56,639 --> 00:04:58,400
i should have used the router a bit more
127
00:04:58,400 --> 00:05:00,160
to get familiar with it instead of using
128
00:05:00,160 --> 00:05:02,479
it straight out of the box i also went
129
00:05:02,479 --> 00:05:03,919
back
130
00:05:03,919 --> 00:05:06,400
and the clamp here you can use an allen
131
00:05:06,400 --> 00:05:07,600
wrench key
132
00:05:07,600 --> 00:05:09,520
and if you just loosen up the clamp you
133
00:05:09,520 --> 00:05:12,000
can then tighten your clip down a little
134
00:05:12,000 --> 00:05:14,479
bit more so it clamps even harder
135
00:05:14,479 --> 00:05:15,919
that way i shouldn't get any of that
136
00:05:15,919 --> 00:05:18,400
adjustability as i go through anymore so
137
00:05:18,400 --> 00:05:19,680
just the thing to know when you're using
138
00:05:19,680 --> 00:05:22,400
this but still all in all really great
139
00:05:22,400 --> 00:05:24,840
router love it
140
00:05:24,840 --> 00:05:52,230
[Music]
141
00:05:52,240 --> 00:05:54,000
now i'm using some drywall screws to
142
00:05:54,000 --> 00:05:56,240
mount the t-track because i really like
143
00:05:56,240 --> 00:05:58,130
the black hardware look
144
00:05:58,130 --> 00:06:03,430
[Music]
145
00:06:03,440 --> 00:06:05,280
since t-track is made of aluminum you
146
00:06:05,280 --> 00:06:07,280
can cut it on a miter saw with a carbide
147
00:06:07,280 --> 00:06:10,160
tip blade i use a retired carbide tip 10
148
00:06:10,160 --> 00:06:11,919
inch blade whose wood cutting days are
149
00:06:11,919 --> 00:06:14,160
gone but its t-track days are bright
150
00:06:14,160 --> 00:06:15,759
just make sure to label it because it
151
00:06:15,759 --> 00:06:18,080
really won't cut wood after
152
00:06:18,080 --> 00:06:20,000
after a quick once-over with the file to
153
00:06:20,000 --> 00:06:21,680
clean up the burrs off the end it's
154
00:06:21,680 --> 00:06:24,280
ready to drop in
155
00:06:24,280 --> 00:06:58,550
[Music]
156
00:06:58,560 --> 00:07:00,400
and with that the t-track is in it
157
00:07:00,400 --> 00:07:02,160
really is super simple and it looks
158
00:07:02,160 --> 00:07:04,400
really great and as for my review of the
159
00:07:04,400 --> 00:07:07,440
dewalt 20 volt max compact router this
160
00:07:07,440 --> 00:07:09,360
thing does not lack in power whatsoever
161
00:07:09,360 --> 00:07:10,479
and i think it really is a great
162
00:07:10,479 --> 00:07:12,639
addition if you already have a dewalt
163
00:07:12,639 --> 00:07:14,800
system now i should add dewalt is not
164
00:07:14,800 --> 00:07:16,400
sponsoring this video at all they're not
165
00:07:16,400 --> 00:07:18,000
telling me to say nice things about this
166
00:07:18,000 --> 00:07:20,319
i just really like dewalt tools and i've
167
00:07:20,319 --> 00:07:21,919
been wanting to get the battery-powered
168
00:07:21,919 --> 00:07:24,240
router for a while and i gotta say it's
169
00:07:24,240 --> 00:07:26,639
awesome definitely worth the money so if
170
00:07:26,639 --> 00:07:27,919
you're interested at all i'll link it
171
00:07:27,919 --> 00:07:29,520
down below in the description
172
00:07:29,520 --> 00:07:32,000
and as always if you like this video hit
173
00:07:32,000 --> 00:07:33,759
the like button for me because it helps
174
00:07:33,759 --> 00:07:35,599
me out a lot helps the channel out a lot
175
00:07:35,599 --> 00:07:36,880
and leave a comment let me know what
176
00:07:36,880 --> 00:07:38,639
you're thinking let me know what you
177
00:07:38,639 --> 00:07:40,639
think about the dewalt router yourself
178
00:07:40,639 --> 00:07:42,479
and as always hit the subscribe button
179
00:07:42,479 --> 00:07:44,240
so you can stay up to date on all of my
180
00:07:44,240 --> 00:07:46,080
videos because i got plenty more
181
00:07:46,080 --> 00:07:47,599
projects coming thanks for watching and
182
00:07:47,599 --> 00:07:51,000
i'll see you next time12265
Can't find what you're looking for?
Get subtitles in any language from opensubtitles.com, and translate them here.