Would you like to inspect the original subtitles? These are the user uploaded subtitles that are being translated:
1
00:00:11,480 --> 00:00:16,600
So again in this topology we need to configure BGP on Route 1.
2
00:00:17,810 --> 00:00:28,540
Yes write a 1 IP addresses configured on Route 1 or 10 dot wondered 1 2 5 4 on gigabit 0 slash 0 slash
3
00:00:28,630 --> 00:00:29,200
0.
4
00:00:29,710 --> 00:00:35,020
And we have this loop back address configured in global configuration mode.
5
00:00:35,020 --> 00:00:47,020
We need to configure a DHB excluded range so IP DCP excluded address range tend not one tenth of 1 to
6
00:00:47,020 --> 00:00:57,880
10 to 1 to 10 10 that completes the exclusion of the first 10 IP addresses for VLAN 10.
7
00:00:58,120 --> 00:01:09,780
I need to do something similar for VLAN 20 and now we can create a DHB pools the first pull is going
8
00:01:09,780 --> 00:01:20,690
to be called a VLAN 10 the network is gonna be tendered one and tendered 0 with a slash 24 mask.
9
00:01:20,740 --> 00:01:25,020
The default router is going to be the switch.
10
00:01:25,090 --> 00:01:30,830
Now we need to know what the IP address is of the switch on the switch.
11
00:01:30,850 --> 00:01:40,510
Show IP interface brief scrolling down we can see that on VLAN 10 this is the IP address of the switch.
12
00:01:40,510 --> 00:01:43,380
And this is the IP address on VLAN 20.
13
00:01:43,510 --> 00:01:50,850
So we need to configure the switch as the default gateway so that would be tendered one to 10 dot 1
14
00:01:53,220 --> 00:01:53,670
again.
15
00:01:53,670 --> 00:02:03,270
Per this IP address configured on VLAN 10 on the switch we told that the DNS server needs to be the
16
00:02:03,270 --> 00:02:14,460
router so DNS server tendered one to 10 to 5 for a gain to show IP interface brief shows us that this
17
00:02:14,460 --> 00:02:17,670
is the IP address of the router.
18
00:02:17,820 --> 00:02:28,300
So I've done that wrong that needs to be tendered one not one not two five four.
19
00:02:28,530 --> 00:02:31,290
So let's look at our configuration.
20
00:02:31,460 --> 00:02:36,780
There's the first DCP pull network looks correct.
21
00:02:36,960 --> 00:02:46,180
Default gateway is the switch DNS server is the router in your exam use show run.
22
00:02:46,320 --> 00:02:53,580
If the command is supported in your simulations to check your work make sure you haven't made a mistake
23
00:02:53,670 --> 00:02:54,540
like I did.
24
00:02:56,370 --> 00:03:03,820
The next DHB poll that we need to configure is V Line 20.
25
00:03:04,340 --> 00:03:14,400
If the network care will be tendered one to 22 0 default broader will be tendered one not twenty one.
26
00:03:15,000 --> 00:03:24,590
Again we can see that on the switch by using the show IP interface brief command or show run.
27
00:03:24,780 --> 00:03:35,090
Scroll down and we can see the IP address on VLAN 20 DNS server tendered wondered 1 to 2 5 4 which is
28
00:03:35,090 --> 00:03:42,800
the right to once again show run allows us to check our configuration that looks good.
29
00:03:43,620 --> 00:03:53,570
Let's make sure that we can ping the switch which has IP address 10 1 1 1 on V land 1 ping succeeds
30
00:03:54,560 --> 00:03:56,790
again on the switch.
31
00:03:56,790 --> 00:04:04,970
There's the IP address on V land 1 or show IP interface brief would allow us to see the IP address on
32
00:04:04,970 --> 00:04:06,550
V land 1.
33
00:04:06,590 --> 00:04:08,000
If you're not sure about that.
34
00:04:08,000 --> 00:04:11,360
Have a look at your lab topology.
35
00:04:11,360 --> 00:04:17,900
You could either use shows to be neighbors to confirm whether things are working right.
36
00:04:17,900 --> 00:04:20,090
In this example CTP wasn't enabled.
37
00:04:22,990 --> 00:04:25,340
In the exam you may not be able to do that.
38
00:04:25,360 --> 00:04:27,810
So have a look at your topology.
39
00:04:27,850 --> 00:04:36,610
Have a look at the running configuration we can see here that that interface hasn't got V'landys configured
40
00:04:37,090 --> 00:04:40,270
so it belongs to villain 1.
41
00:04:40,450 --> 00:04:49,420
Or we could use this command show interface gigabit 1 0 1 switch port to see which v lan this interface
42
00:04:49,420 --> 00:04:50,600
belongs to.
43
00:04:50,830 --> 00:04:56,230
You can see it belongs to v land 1 shows to be neighbor.
44
00:04:56,410 --> 00:05:00,600
Hopefully at some point will show us a neighbor relationship.
45
00:05:00,640 --> 00:05:08,510
We can see on the road as an example that the switch is connected via gigabit.
46
00:05:08,510 --> 00:05:15,440
1 0 1 to the router on gigabit 0 slash 0 slash 0.
47
00:05:16,660 --> 00:05:28,050
So we've confirmed the cabling and we can ping the switch now we've configured DHB on the router but
48
00:05:28,110 --> 00:05:31,960
the rod is separated by a layer 3 switch.
49
00:05:32,010 --> 00:05:39,030
We need to do some configuration on the switch to allow DCP request messages to be forwarded to the
50
00:05:39,030 --> 00:05:40,110
router.
51
00:05:40,230 --> 00:05:43,620
So now we need to do some configuration on the switch to enable that.
52
00:05:44,370 --> 00:05:51,390
So don't forget that in some of these labs you have to do configuration on multiple devices.
5422
Can't find what you're looking for?
Get subtitles in any language from opensubtitles.com, and translate them here.