Would you like to inspect the original subtitles? These are the user uploaded subtitles that are being translated:
1
00:00:13,120 --> 00:00:18,840
So we need to configure enable and BQ want passwords to help us with us.
2
00:00:18,850 --> 00:00:20,290
We can use Notepad
3
00:00:23,830 --> 00:00:24,180
now.
4
00:00:24,190 --> 00:00:34,570
I know these commands so I could simply type them out like this from memory.
5
00:00:34,570 --> 00:00:41,050
I've done this for many years so I can type that out from memory but let me show you how to do that
6
00:00:41,920 --> 00:00:43,390
through the CLIA.
7
00:00:44,200 --> 00:00:50,250
And then we'll use the script to copy and paste the commands on remaining devices.
8
00:00:50,530 --> 00:00:57,030
So on the Code Switch notice when I type enable I'm directly in privilege mode.
9
00:00:57,400 --> 00:01:07,400
So I want to set and enable password so enable password and specify a password now it's recommended
10
00:01:07,490 --> 00:01:13,550
that you use a secret password rather than an enable password.
11
00:01:13,550 --> 00:01:21,730
They shouldn't be the same as we can see there but notice it is accepted by the router or switch.
12
00:01:21,980 --> 00:01:29,990
So in the exam just read carefully whether they want an enable password configured or a secret password
13
00:01:30,410 --> 00:01:33,890
configure the one that they ask you to configure.
14
00:01:33,950 --> 00:01:41,450
So if I type disable now and type enable notice I need to put in my secret password not enable because
15
00:01:41,450 --> 00:01:45,890
secret takes precedence over enable.
16
00:01:45,890 --> 00:01:55,050
And typically in the real world you want to configure a enable password we need to configure Viti why
17
00:01:55,050 --> 00:02:05,420
lines will use the most common version of this VQ why 0 to 4 which is the first 5 V.T. y lines I'm going
18
00:02:05,420 --> 00:02:12,620
to type a log in and notice we have to specify a password in the order of this command and this command
19
00:02:12,680 --> 00:02:13,970
don't matter.
20
00:02:13,970 --> 00:02:21,470
You can either use password Cisco first or log in first but essentially both have to be configured for
21
00:02:21,470 --> 00:02:22,400
it to work.
22
00:02:23,630 --> 00:02:26,000
So we've configured and enable password
23
00:02:28,560 --> 00:02:32,580
and we've configured to V.T. why lines on the switch.
24
00:02:32,760 --> 00:02:41,720
I'll save that config and what I'll do now is simply copy this and I'll use that on other switches.
25
00:02:41,860 --> 00:02:42,120
Okay.
26
00:02:42,130 --> 00:02:43,480
There was a problem here.
27
00:02:47,800 --> 00:02:58,160
This should be enable password so let's copy that in again paste it in notice.
28
00:02:58,160 --> 00:03:05,370
In this case the enable command wasn't accepted because we're in line config mode.
29
00:03:05,600 --> 00:03:06,830
Neither was confetti
30
00:03:10,030 --> 00:03:12,310
but that's okay in this scenario.
31
00:03:12,310 --> 00:03:18,310
Notice the enabled password was configured and the V2 Y was configured.
32
00:03:18,340 --> 00:03:24,360
What I suggest you do is make sure that the commands are accepted.
33
00:03:24,580 --> 00:03:33,680
If at any point they look like they not accepted double check everything manually do the same on the
34
00:03:33,680 --> 00:03:43,370
Access Switch and I'll just do this one manually just to show you the point about the logging.
35
00:03:45,400 --> 00:03:50,710
So notice if I go into the V2 y line and I use password Cisco and then type of log in
36
00:03:53,700 --> 00:03:57,350
I don't get the message that the password has to be configured.
37
00:03:57,630 --> 00:04:04,790
But the result is the same as it is on other switches.
38
00:04:04,790 --> 00:04:08,190
So on switch one notice the result here.
39
00:04:09,750 --> 00:04:12,440
Is the same as the result here
40
00:04:17,460 --> 00:04:20,410
do something similar on axis 3.
41
00:04:20,520 --> 00:04:28,560
Paste the configuration in and save it and then I'll do something similar on the router
42
00:04:32,270 --> 00:04:32,880
okay.
43
00:04:32,930 --> 00:04:37,810
So we've now configured and enabled password and v2 y password of Cisco.
44
00:04:37,910 --> 00:04:41,160
We can't test the V2 y passwords yet.
45
00:04:41,330 --> 00:04:43,490
We need IP addresses for that.
46
00:04:43,490 --> 00:04:47,930
But before we do that we need to do some villain configuration.
4574
Can't find what you're looking for?
Get subtitles in any language from opensubtitles.com, and translate them here.